Home/Guides/MIL-STD-810H

Guide · Certification

MIL-STD-810H explained, and what “compliant” leaves out

A US military handbook of environmental test methods, not a single test and not a certificate. How to read the claim on a rugged phone box, and the questions it leaves open.

MIL-STD-810H is a US Department of Defense standard, published in 2019, that describes how to tailor and run environmental tests: drops, vibration, heat, cold, rain, dust, salt fog and more, across some 29 laboratory methods. It is not a pass-or-fail certificate and no government body certifies phones against it. A phone marked “MIL-STD-810H” has been tested to some of those methods, chosen by the manufacturer, usually without publishing which ones or by whom.

What the standard is

MIL-STD-810 has existed since 1962 to make sure military equipment survives the conditions it will meet in service. The current edition, 810H, was issued in January 2019 and amended in 2022. Part One is about tailoring: deciding which tests matter for a given piece of equipment and how hard to make them. Part Two is the menu of laboratory methods.

That design is the root of the confusion. The standard expects the buyer and the supplier to agree a tailored test plan. On a consumer phone there is no buyer in the room: the manufacturer picks the methods, the severities and the lab, and writes “MIL-STD-810H” on the box.

The methods most often cited for phones

Selected MIL-STD-810H Part Two laboratory methods. The number after the dot is the method revision.
MethodTestWhat it simulates
500.6Low pressure (altitude)Air freight, mountains; seal and battery behaviour
501.7 / 502.7High / low temperatureOperation and storage in heat and cold
503.7Temperature shockSudden moves between hot and cold
506.6RainDriving and dripping rain
507.6HumidityLong exposure to damp heat
509.7Salt fogCorrosion in coastal air
510.7Sand and dustBlowing dust and sand
514.8VibrationVehicle transport
516.8Shock, including transit dropBeing dropped while handled or carried

The drop test, and why the box height differs

The method buyers care about most is 516.8, procedure IV, the transit drop. For small items carried by a person, the default schedule is 26 drops from 122 cm (4 ft): one on every face, edge and corner. Two details matter. The standard allows those 26 drops to be spread over up to five units, so no single phone has to survive all of them. And 810H changed the default impact surface to steel plate over concrete, where 810G used plywood over concrete; older claims and newer ones are not directly comparable.

Drop heights printed by Ulefone are separate manufacturer claims. The Armor 33 Pro is listed as drop-proof to 1.8 m and the Armor Mini 5 to 2 m, both higher than the standard's default. Ulefone does not publish the surface, the number of drops or the number of units behind those figures.

What “compliant” leaves out

  • Which methods“MIL-STD-810H” alone does not say whether the phone was drop-tested, heat-tested, salt-fog-tested or all three.
  • Which severityEach method has parameters — temperatures, durations, heights — that the tester can tailor up or down.
  • Who ran itThere is no official certification. Tests can be run in-house or by an independent lab, and the report is rarely public.
  • How many unitsAs with the drop test, a sequence can be split across several samples, which is legitimate but not the same as one phone surviving everything.
  • Real-world fallsA lab drop is a controlled fall onto a flat surface. A phone landing on its camera bump on a rock, or after a previous impact, is a different event.
Same claim, every brand

This is not specific to Ulefone. Almost every rugged phone brand prints the same unqualified “MIL-STD-810H” line, so it does not separate one brand from another. What separates them is detail, and detail is almost never published.

How to use the claim when buying

  • Ask for the method listIf you are buying for a team, ask the seller or distributor which methods and severities were tested, and by which lab. A real answer is a good sign.
  • Read drop claims as the maker's ownA stated drop height tells you what the manufacturer is prepared to claim, not what the standard requires.
  • Weigh owner reportsPatterns in owner reports, such as cracked camera housings, say more about real falls than the label. See what Ulefone owners report.
  • Pair it with the water ratingMIL-STD-810H rain and immersion methods are not the same as IP68 or IP69K. See IP68 vs IP69K.

Common questions

What does MIL-STD-810H mean on a phone?

It means the manufacturer says the phone was tested to some of the environmental test methods in the US military standard MIL-STD-810H, such as drop, vibration, temperature or dust. It does not say which methods, how severe, or who tested it.

Is MIL-STD-810H a certification?

No. It is a test-method standard. No government body certifies consumer phones against it; manufacturers choose and run, or commission, the tests themselves.

What drop height does MIL-STD-810H require?

The default transit-drop schedule for small carried items is 26 drops from 122 cm (4 ft) onto every face, edge and corner, which may be spread over up to five units. Manufacturers can tailor the height, and many print their own, higher figures.

What is the difference between MIL-STD-810G and 810H?

810H (2019) replaced 810G (2008). It revised most test methods; for the transit drop, it changed the default impact surface from plywood over concrete to steel over concrete.

Are Ulefone phones MIL-STD-810H certified?

Ulefone describes its Armor phones as certified to MIL-STD-810H, but it does not publish the list of methods or the test reports. As with other brands, treat it as a manufacturer claim.

Sources checked

  1. US Department of Defense, MIL-STD-810H, Environmental Engineering Considerations and Laboratory Tests (31 January 2019; Change Notice 1, 2022), Part One and Part Two methods 500.6 to 528.1.
  2. Rugged PC Review, “How the rugged PC ‘drop spec’ just became different”, on the 810H change of impact surface.
  3. MobileDemand, “Is your tablet case MIL-STD certified and tested?”, and Delserro Engineering Solutions, “Method 516, procedure IV – transit drop”, for the 26-drop schedule and the five-unit allowance.
  4. Ulefone product pages for the Armor 33 Pro (1.8 m) and Armor Mini 5 (2 m) drop claims. ulefone.com

Method numbers and the transit-drop schedule are from the MIL-STD-810H text and published test-lab summaries. Ulefone drop heights are manufacturer claims, checked 2026-11-18.